Universal interface CC2 (2 IN / 2 OUT)

Code: EK-CC2-TP

Description

The Ekinex® universal interface EK-CC2-TP is a KNX device which can be used as input and/or output module.

The device is equipped with inputs to connect the KNX bus to switches, pushbuttons or classic sensors (normally not communicating on the KNX bus) or any binary signals from other devices, in order to control KNX bus functions, and control outputs for low consumption LEDs.

The voltage for polling the inputs is supplied within the device. The device integrates a KNX bus communication module and is realized for flush-mounting or for mounting on a standard 35 mm DIN-rail. The device is powered by the KNX bus and does not require auxiliary power supply.

Power supply

•30 Vdc power supply by KNX bus
•Current consumption from bus < 10 mA

Delivery

Delivery includes a terminal block for connection to the bus.

Accessories

Support for mounting on a standard 35 mm DIN-rail (code EK-SMG-35) and spring for snapping on the back of Ekinex® wall-mount devices (code EK-MAR) to be ordered separately.

Functions and Application Areas

On / Off Switching

Independent switching on and off of single electrical loads or load groups.

Dimming Control

Adjusting light intensity through short/long press actions or coupled input pairs.

Shutter and Blind Drives

Full movement up/down and precise step-by-step slat positioning for motorized shading.

Signal & Alarm Status Detection

Real-time state detection of signaling contacts from security equipment or technical alarms.

Scene Recalling and Saving

Instant recalling and memorizing of pre-configured lighting and comfort scenes.

Sending Values on Bus

Sending temperature, brightness, percentage or counter values over the KNX bus.

Pulse & Switching Cycle Counter

Counting input signal transitions and cycles for energy and maintenance tracking.

Low-consumption LED Outputs

Driving 2 low-consumption LEDs for status feedback, orientation nightlights, or visual alerts.

Technical Data

Power Supply

Power Supply30 Vdc SELV from KNX bus line

Current Consumption< 10 mA

Inputs and Outputs

Number of Inputs2 for potential-free contacts

Polling VoltageProduced inside the device

Number of Outputs2 for low-consumption LEDs (+5V common)

Terminals (I/O)Screw terminal blocks (max 1 mm² wire, max 0.2 Nm torque)

Bus ConnectionStandard KNX terminal block (red / black, 0.6 - 0.8 mm)

Physical Characteristics

HousingPlastic casing

MountingFlush-mounting wall box, 35 mm rail with EK-SMG-35 or EK-MAR spring

Protection DegreeIP20 (installed device to EN 60529)

Mechanical Classification3M2 (to EN 50491-2)

Pollution Degree2 (to IEC 60664-1)

Dimensions43 x 43 x 16 mm (W x H x D)

Weight20 g

Environmental Conditions

Operating Temperature-5°C ... +45°C

Storage Temperature-25°C ... +55°C

Transport Temperature-25°C ... +70°C

Relative Humidity95% non-condensing

Climatic Classification3K5 (to EN 50491-2)

Delivery

Delivery includes a terminal block for connection to the bus.

Accessories

Support for mounting on a standard 35 mm DIN-rail (code EK-SMG-35) and spring for snapping on the back of Ekinex® wall-mount devices (code EK-MAR) to be ordered separately.

Functions / Features

Plastic casing

Programming pushbutton and LED on the case

Connection to bus line with KNX terminal block

Screw terminal blocks for connecting inputs and outputs

IP20 protection degree (installed device)

Weight 20 g

Configuration and Commissioning

A detailed description of the parameters can be found in the application manual of the device. Configuration and commissioning require ETS5 2.0 or later versions. ETS application program: APEKCC2TP01.knxprod (or current release). Max 93 communication objects and 255 group addresses.